Aug 25, 2015 - EZLockEZ100Manual - Free download as PDF File (.pdf) or read online for free. This is the manual for the EZ-Lock EZ 100 Serger. 20680 E-Z MT Lug $72.00 20681 E-Z MT Lug Slide $19. 22170 Lock Nut $29.50 22230 Nylon Nut $29.50. I don't know a whit about sergers. About 6 years ago I inherited an E-Z Lock E-Z100 machine. I'm finally getting the nerve up to see if I can use it. One of the reasons I've never used it is because it didn't come with a manual and I couldn't find any info about this brand online. I'm hoping to have better luck this time around. Anyway, the point of this story is that I wanted to share this manual with those other's of you that I saw looking for it, free of charge and NO HASSLES! Click to open and save the PDF file EZ-Lock EZ100 Owner's Manual Too bad for me it doesn't come with a brain!
EZ-100 Mounting Bracket
Features
• New and retrofit installations
• Easy and fast installation (drill and tap)
• No extra brackets or hardware required
• 1/2 inch - 13 UNC 2A thread
• Includes 255-EZ Pulser Disc (other EZ Pulser Disc
models available)
• Rated for use up to 300 rpm (for information about
use with higher speeds, consult factory)
Can be used with the following shaft speed switches and sensors:
• 907 XP
• M100
• M100T
• FB420
• SpeedTalker DN-XP
EZ-SCP Mounting Bracket
Features
• New and retrofit installations
• Easy and fast installation (drill and tap)
• No extra brackets or hardware required
• 1/2 inch - 13 UNC 2A thread
• Includes 255-EZ Pulser Disc (other EZ Pulser Disc
models available)
• Rated for use up to 300 rpm (for information about
use with higher speeds, consult factory)
Can be used with the following shaft speed switches:
• SCP1000 / SCP2000
EZ Mounting Magnet Option for Untapped Shafts
MM-2.00 Mounting Magnet
• No drilling or Tapping Needed
• Must be used with Mounting Brackets EZ-100 or EZ-SCP
• Used with M100, 907 XP, M100T, FB420, SCP1000 / SCP2000,
SpeedTalker DN-XP
Sewing with nancy ezlock serger, sewing with nancy serger. Baby Lock Bobbin Cases. Instructional Manuals.
Advertisement
E-z Lock Ez100
Summary of Contents for ESP EZ-LOCK
E-z Lock Ez100 Serger Sewing Machine
E Z Lock Ez100 Manual Meat Packing
- Page 1 U S ER MANUAL...
- Page 2 *Note:- for use with Magnetic lock only Functions of the EZ-LOCK The EZ-LOCK can control up to two doors by use of pin numbers. Selectable Pin number length 2,3,4,5 and 6 digits (per zone). Programmable door open time 00 to 99 seconds.
- Page 3 Sighting Of The EZ-LOCK Site the EZ-LOCK within easy access to the door/doors to be controlled. Recommended mounting height 1.2m. Fitting Using the template mark and drill the fixing and cable entry holes. Remove security screw from the underside of the keypad and remove back plate.
- Page 4 Wiring Diagram and connections Brown-door status detecting - reed switch Orange-push to exit button - Zone 1 Yellow-push to exit button - Zone 2 Green - COM Door contact - reed switch Exit button - Zone 1 Exit button - Zone 2 Additional power supply for lock Not Used...
- Page 5 Wiring Diagram for Maglock EV-BPS 240vAC INPUT Push button E.lock DC out Timer GND P.B Exit Button 0-20 secs Capacitor Maglock 0.47uF 100v Emergency door release Wiring Diagram for Yale Release EV-BPS 240vAC INPUT Push button E.lock DC out Timer GND P.B Exit Button 0-20...
- Page 6 Brief details of programming Access To programming mode. Programme pin numbers. There are two locations for entering pin numbers (zone 1 and zone 2). Zone 1 has 1000 locations available 000-999. Zone 2 has 10 locations available 00-09. Select the lock release times (00-99 seconds) zone 1 and zone 2. How to escape programming mode.
- Page 7 Setting the Unlock Time for Zone 1 1. Enter programming mode. A Long bleep will be heard and the green power LED will turn orange. 2. Press the key then the 1 key the orange LED will start to flash 3.
- Page 8 How to Change the Programming Pin Number 1. Enter programming mode. A Long bleep will be heard and the green power LED will turn orange. 2. Press key followed by the 3 key the orange LED will start to flash. 3.
- Page 9 How to load factory default settings 1. Enter programming mode. A Long bleep will be heard and the green power LED will turn orange. 2. Press the key followed by the 8 key the orange LED will start to flash. 3.
- Page 10 How to set the length of the pin numbers to be used 1. Enter programming mode by entering the 4 digit pin number twice (default pin 1234). A Long bleep will be heard and the green power LED will turn orange. 2.
- Page 11 How to reset a lost programming pin number Note:- this will set the programming Pin back to its default factory setting of 1234 and leave all other settings intact provided Pin length is still 4 digits. 1. Remove power to the keypad/reader for 10 seconds. 2.
- Page 12 Technical Specification DC input 12 - 24volts AC input 12 - 24volts Standby current 80ma Operating current (without lock) 110ma Working temperature -20c to +50c IP rating Dimension 152 x 45 x 25mm Elite Security Products Telephone: 01527 515150 Unit 7, Target Park, Shawbank Rd Fax: 01527 51 51 43 Lakeside, Redditch B98 8YN email: info@espuk.com...